Volume 4, Issue 3 (Fall 2020)                   ijcoe 2020, 4(3): 1-14 | Back to browse issues page

XML Print

Download citation:
BibTeX | RIS | EndNote | Medlars | ProCite | Reference Manager | RefWorks
Send citation to:

Yasseri S. Seismic Design of Subsea Spool per ISO: Part III- Analysis & Design. ijcoe. 2020; 4 (3) :1-14
URL: http://ijcoe.org/article-1-197-en.html
Brunel University London
Abstract:   (325 Views)
This is the final part of a three-part paper that presents the methodology, data needed, code check of 12-inch ID rigid pools, describing the design methodology, and key design parameters for performing the analyses. Discussion of the state of art regarding the soil data is covered in Part I. Part II is dedicated to describing ISO 19901 and 19902 seismic qualification and the derivation of design time histories. 
For each cluster end, there are two parallel flowlines each individually terminated with a Flowline Termination Assembly (FTA).  The FTA is free to move axially on its foundation to absorb movement caused by the flowline expansion and walking.  Lateral movement is restricted by lateral stops on the foundation.  Two separate spools will then be connected to a single Pigging Loop Module with a piled foundation.  A diver-less horizontal collet connector system will be used for the tie-in at both ends of the spool.
The analysis methodology which assumes the seabed is a compliant plate, is described in this paper.  For validation purposes, a couple of configurations were used to create a full three-dimensional model where the soil was modeled using the solid element with Moh-Columb behavior. These results are not presented in this paper. 
Full-Text [PDF 990 kb]   (125 Downloads)    
Type of Study: Applicable | Subject: Coastal Engineering
Received: 2020/08/28 | Accepted: 2020/12/29 | ePublished: 2021/02/20

1. Abaqus, Simulia by Desualt systems, 2014. Version 13.
2. American Society of Civil Engineers (ASCE), ASCE 7-10, Virginia (2010). Minimum Design Loads for Buildings and Other Structures
3. ASME VIII 2011a, Div2 Part 5 Design By Analysis Requirements
4. ASME B31.8 Gas Transmission and Distribution Piping Systems
5. Chang, B., Abraham, M., and B.-F. Peng, B.F., (20015), Comparison of ISO and API Seismic Design Guidelines Using Three Existing Offshore Platforms, OTC 17285, Offshore Technology Conference, Houston, TX, U.S.A., 2-5 May 2005. [DOI:10.4043/17285-MS]
6. El Naggar, M. H. & Bentley, K. J., (2000), Dynamic analysis for laterally loaded piles and dynamic p-y curves. Canadian Geotechnical Journal, 37, 1166-1183 [DOI:10.1139/t00-058]
7. Eurocode 8: Seismic Design of Buildings
8. ISO 19901-2, (2004) Petroleum and Natural Gas Industries - Specific Requirements for Offshore Structures - Part 2: Seismic Design Procedures and Criteria
9. Marshall, P.W. and Chang, B, (1996), Structural Design Considerations" OTC 8107, Offshore Technology Conference, Houston 1996. [DOI:10.4043/8107-MS]
10. Naeim, Farzard, (1989), The Seismic Design Handbook, Van Nostrand Reinhold, USA. [DOI:10.1007/978-1-4615-9753-7]
11. Peng. B.F., Abdel Ghoneim, G., (2009), Comparison of ISO and API Seismic Design Requirements for Offshore Structures Proceedings of the Nineteenth (2009) International Offshore and Polar Engineering Conference Osaka, Japan, June 21-26, 2009
12. Yasseri, S, (2020), Seismic Design of Subsea Jumper per ISO: Part I- Preliminaries, IJCOE Vol.4/No. 1/Spring 2020 (31-43) [DOI:10.29252/ijcoe.4.1.31]
13. Yasseri, S. (2020), Seismic Design of Subsea Spool per ISO: Part II- Seismic Requirements, IJCOE Vol.4/No. 2/Summer 2020 (1-13)
14. SAFEBUCK JIP - Safe Design of Pipelines with Lateral Buckling, Design Guideline, Safebuck III

Add your comments about this article : Your username or Email:

Send email to the article author

© 2021 All Rights Reserved | International Journal of Coastal and Offshore Engineering